The 3-meter LED garland "Horse Tail" with 10 rays and white illumination for decorating a New Year tree and interior spaces, presented in a question-and-answer format.



LED garland “Horse Tail” installed on a Christmas tree, FAQ and instruction overview

Frequently Asked Questions about the LED Garland "Horse Tail"

User reviews of the garland "Horse Tail" >>>

Technical Specifications of the LED Garland "Horse Tail"

What is the LED garland of the "horse tail" type and what is its design?

The LED garland of the "horse tail" type represents a bundle of thin wired strands with diodes, which are gathered at the upper point into a common node or plastic cone. From this bundle, rays of equal length extend downward, and from the same upper point a power cable leads to the supply unit and plug. The number of strands depends on the modification and usually amounts to 10, 20, or 30 pieces; each strand carries LEDs along its entire length.

How many strands and LEDs can the garland "horse tail" have?

Within the "horse tail" garland product range, variants are available approximately with the following combinations: 2 m with 10 strands and about 200 diodes, 2 m with 20 strands and about 400 or 800 diodes, 3 m with 10 strands and about 300 diodes, 3 m with 20 strands and about 600 diodes, 3 m with 30 strands and about 900 diodes, as well as 3 m with 1200 diodes. Practical use has demonstrated that typically each strand contains approximately 30 LEDs, and the selection of the number of strands and lamps affects the brightness and density of illumination.

What wire (conductor) color is used in the garlands "horse tail"?

For the "horse tail" garlands, two main wire options are used: transparent or silver (often specified in the description as white), and green. Transparent or silver wire is less noticeable on light-colored and snow-covered trees, whereas green wire is optimal for classic green trees, where it visually blends with the needles.

What is the length of the power cord and where is the plug located?

In different modifications of the garland, the length of the power cable varies. For certain models, the length of the cord from the upper bundle to the plug is approximately 40–50 cm; for others, an extended cable of about 3 m from the bundle to the plug is provided. The plug is usually located at the end of the cable extending from the upper point of the garland; therefore, when installed on a tall tree, a standard household extension cord is almost always required for connection to the socket.

What is the distance between LEDs on a single strand?

For the "horse tail" garlands, the manufacturer specifies a distance between LEDs of approximately 10 cm. Due to such spacing, the diodes form a uniform luminous line along the entire length of each strand.

What glow color options are available for the garlands "horse tail"?

For the LED garlands "horse tail", glow options are available with warm white light (approximately 4000 K, with a more yellowish hue), cool white light, as well as multicolored (multi-color) modifications. Switching between warm, cool, and multicolored modes is not provided in classical models; the glow color is determined by the specific type of garland.

Is it possible to connect several garlands "horse tail" together into a single electrical circuit?

The design of the "horse tail" garlands does not provide for series or parallel connection of several products via standard connectors. Each garland has its own power supply unit and is connected to the mains separately. It is permissible to plug several garlands into one household extension cord; however, electrically they remain independent.

.

How many operating modes does the garland support and is there a static mode without flashing?

Most "horse tail" garlands are equipped with a controller featuring eight operating modes: seven flashing variations and one static mode without blinking, in which all LEDs emit continuous light. In certain series, modifications are available that provide only a static mode, but with increased brightness. When selecting a specific model, it is necessary to refer to the current product description and user instructions.

Is it possible to fix the selected illumination mode of the garland?

The availability of mode memory depends on the batch and the specific model. For some garlands, a memory unit is implemented that stores the last selected mode (including flashing modes) when disconnected from the mains. In other series, the manufacturer officially guarantees fixation only of the static mode, while flashing modes may switch sequentially in automatic order. In all cases, static continuous illumination can be maintained until another mode is selected.

How does the timer on the garland remote control operate?

The timer in the supplied remote controls for the "horse tail" garlands initiates an automatic on/off cycle without the possibility of manual interval adjustment. According to the manufacturer’s information and practical experience, two typical operating variants are encountered: a mode of 6 hours on and 18 hours off, or a mode of 8 hours on and 8 hours off. The specific operating pattern depends on the production batch; however, in both cases the timer is activated by a single press of the corresponding button, after which the garland switches on and off cyclically without further user intervention.

What is the approximate service life of the garland "horse tail"?

The service life of the LED garland "horse tail" is not officially limited to a fixed period and depends on careful operation. If the instructions are followed, the wires and connectors are handled with care, and the power supply unit is protected from moisture, the product may be used for an extended period over several seasons.

Can the garland be used outdoors and what is the operating temperature range?

Some "horse tail" garlands are intended exclusively for indoor use, while certain models are equipped with an outdoor-rated power supply featuring moisture protection and may be used outdoors. For indoor modifications, standard household conditions without exposure to precipitation should be observed. For outdoor models, the permissible temperature range is specified in the description, usually from −10 to +35 ℃, and for some outdoor versions up to −40 ℃. In all cases, it is recommended to additionally protect the power supply unit from direct water exposure and not to switch on the garland immediately after exposure to severe frost without prior acclimatization.

What is typically included in the package of the garland "horse tail"?

The standard package includes the garland itself with a bundle of strands and a control unit, a mains cable with a plug, and, depending on the model, a remote control. The power supply unit is included in the package and no additional adapters are required. An extension cord for connection to a distant socket is not included and, if necessary, is purchased separately.

Are all models of the garlands "horse tail" equipped with a remote control?

A remote control is not included in the package of all modifications of the "horse tail" garland. The assortment includes versions without a remote, as well as updated series in which the remote control is already included and allows changing modes, adjusting brightness, and controlling the timer. Information regarding the presence of a remote control is îáÿçàòåëüíî specified in the description of the specific item; in case of discrepancy in the package contents, it is recommended to arrange a return due to incomplete configuration.

Is it possible to purchase the power supply unit or the remote control separately from the garland?

According to the seller’s information, power supply units and remote controls for the "horse tail" garlands are not sold separately. In the event of failure of the power supply unit or remote control, it is officially recommended either to use the mode switching functions on the control unit itself (if available) or to process a return of the product due to defect and purchase a new garland of the appropriate configuration.

Is it possible to control several garlands "horse tail" with a single remote control?

For certain models, it is possible to control several identical garlands with a single remote control, provided that all products belong to the same series and are located within the signal range of the remote. At the same time, each garland still has its own separate power supply unit and is connected to the mains individually.

Does the garland operate on batteries or only from the mains?

The typical New Year garland "horse tail" is designed to operate from the mains via the supplied power supply unit, which transforms the voltage to a safe level. The seller’s assortment may include separate similar dew-type garlands powered by batteries; however, the model under consideration is connected to a standard socket and is not intended for operation from AA batteries without a specialized unit.

.

Where is the control unit located and how are the garland controls arranged?

The control unit of the "horse tail" garland is usually located directly below the bundle of strands and is connected to it by a short section of cable. A mode switching button is placed on the housing of the unit, allowing illumination programs to be changed without the remote control. In modifications equipped with a remote control, additional buttons are available for switching on and off, changing effects, adjusting brightness, and activating the timer. The unit itself can be conveniently concealed among the branches of the tree and decorative ornaments.

Which wire color is preferable for a green and for a snow-covered tree?

For a classic green artificial or natural tree, a green wire is optimal, as it visually blends with the needles and is less noticeable when switched off. For white and snow-covered trees, it is recommended to select models with a white or transparent (silver) wire so that the wiring harmoniously matches the overall light decorative concept.

Why does the cool white light of the garland sometimes appear bluish?

The cool white light of the "horse tail" garlands may visually shift toward a bluish hue depending on the color of the walls, decorations, the snow effect on the tree, and the specifics of photography. On white or very light branches, as well as in photographs, certain diodes may appear more blue, although the actual declared color is cool white.

How should the garland "horse tail" be properly installed on a tree?

To install the "horse tail" garland, it is recommended to secure the main bundle of strands or the plastic cone at the top of the tree to the upper branch or tip using wire, a fastening tie, or a durable thread. After fixing the bundle, the strands should be carefully untangled, temporarily winding each strand into a ring if necessary, and then sequentially distributing the rays from the top toward the lower tiers of branches. The strands may be freely placed on the branches without tight winding, achieving uniform light distribution along the entire height of the tree.

Is it possible to hang the garland after the tree has already been decorated with ornaments?

The "horse tail" garland may be installed either before or after placing ornaments; however, it is more convenient to first secure the bundle and distribute the strands, and then adjust the decor. If necessary, the garland can be carefully threaded between baubles and decorations without excessive tension on the wires.

How should the upper bundle of the garland be secured at the top of the tree?

The upper bundle or cone of the garland is secured at the top to a sturdy branch or the tree tip. A plastic fastening tie, decorative wire, or durable thread may be used for fixation; it is important not to compress the wires excessively. After fastening, the cone can be partially concealed within the crown so that it is not visible in the decorative arrangement.

Is it possible to use the strands of the garland as a dew-type garland by winding them around branches?

The strands of the "horse tail" garland may be partially wound around branches, creating a dew-type garland effect. At the same time, it is important not to tighten the wire too strongly around the branches and not to bend the conductors sharply. The design is originally intended for free hanging of the rays; therefore, dense winding is not mandatory.

How should the garland be removed from a natural tree and prepared for storage?

To remove the garland from a natural tree, it is recommended first to disconnect the plug from the mains and lower the strands from the branches without pulling on the diodes. It is convenient, during removal, to wind each strand into a separate ring or small coil, and then secure them with an elastic band or wire, as done in the factory winding. The bundle with strands should be stored in a dry place, which helps prevent significant tangling and prolongs the service life of the LED garland.

How should the garland be switched on and adjusted during first use?

Before first activation, the garland should be installed on the tree, the power supply unit connected to the mains, and, if a remote control is available, the protective plastic insert removed from the battery compartment. Thereafter, illumination modes may be switched using the button on the power supply unit or the buttons on the remote control, and the timer may be activated if required. If the remote does not respond, the CR2025 battery should be checked and the remote directed toward the control unit.

.

How should the garland length and number of lamps be selected according to the height of the tree?

For trees up to 1,5–1,8 m in height, a "horse tail" garland of 2 m with 200 to 400 diodes is usually sufficient. For trees approximately 1,9–2,1 m high, a 2 m garland with 400–800 diodes is often selected, or 3 m for a more pronounced illumination effect. For tall trees of 2,2–2,5 m, a length of 3 m with 600–900 diodes is recommended, and for very dense constructions or trees higher than 2,5 m, a 3 m garland with 900–1200 diodes or several garlands is frequently chosen. Excess strand length may be concealed inside the crown without extending them to the floor.

How many "horse tail" garlands are required for a large tree to achieve a lush and bright appearance?

The number of garlands depends on individual preferences regarding brightness and density of lights. Practice indicates that for a tree approximately 2,2–2,5 m in height, one garland of 3 m with 600–900 diodes is often sufficient to create a festive appearance. If a maximum brightness effect is required or for decoration of public premises, two or more garlands may be used, distributing the bundles at different levels.

How can the effect of illumination “from within” the tree be achieved?

To create an effect of illumination emerging from within the crown, the strands of the "horse tail" garland are recommended to be placed closer to the trunk rather than only along the outer contour of the branches. Some strands may be positioned slightly deeper inside the tree, alternating with outer branches, so that the light softly penetrates through the decor.

Is the garland suitable for small trees approximately 90–120 cm in height?

The minimum length of classic "horse tail" garlands is usually 2 m; therefore, specific models designed exclusively for very small trees (approximately 90 cm) are not presented in the assortment. If desired, such a garland may nevertheless be used on a low tree by carefully concealing the excess length and part of the strands within the crown.

Which glow color is preferable for a green and for a snow-covered tree?

For green trees, warm white light is considered a comfortable option, creating a classic and cozy atmosphere. For white and snow-covered trees, the manufacturer and customers often recommend cool white light, which emphasizes the “winter” character of the decoration. The final selection of the glow color of the "horse tail" garland remains at the user’s discretion and depends on the overall decorative style.

Is it permissible to cut off excess strand length or damaged sections of the garland?

Officially, the manufacturer does not recommend cutting the strands of the garland or modifying its design. It is noted in responses that certain users have trimmed the ends; however, any intervention in the power circuit and the integrity of the conductors is performed at one’s own risk and may result in refusal of warranty service. For safe operation, it is recommended to use the garland without shortening it and not to compromise the integrity of the wires.

Does the garland rust and is it damaged by rain and snow?

In outdoor modifications of the "horse tail" garland, the wires and diodes have basic moisture protection, and the power supply unit is equipped with a moisture-resistant housing. Subject to compliance with the temperature range and protection of the unit from direct water exposure, such garlands may be used on outdoor trees and open structures without risk of corrosion of elements. Indoor models must not be used outdoors, as they are not designed for exposure to precipitation.

How should the garland be stored between seasonal periods of use?

After dismantling, the garland should be completely disconnected from the power supply, carefully removed from the tree, and each strand wound into a separate ring or coil using soft fastening ties or elastic bands. It is recommended to store the product in a dry ïîìåùåíèå, preferably in its original packaging or in a separate container, in order to prevent severe tangling and mechanical damage to the wires and diodes.

What should be done if some strands or diodes do not light up or if the garland emits very dim light?

In the event of partial or complete failure of illumination, the correct connection to the mains and the selected operating mode should first be checked. If the malfunction persists, and certain strands do not illuminate or the diodes glow significantly weaker, the manufacturer recommends arranging a return of the product due to defect through the personal account of the marketplace where the garland was purchased. Independent repair is generally not ïðåäóñìîòðåí and may be unsafe.

.

What should be done if the remote control does not operate or certain buttons do not respond?

If the remote control does not operate the garland, it is necessary to ensure that the protective plastic insert has been removed from the battery compartment, install a new CR2025 battery, and direct the remote control toward the control unit. If the issue persists, the garland modes may be switched using the button on the power supply unit. Separate sale of remote controls is not provided; therefore, upon confirmation of malfunction, it is recommended to arrange a return of the garland as a defective product.

Is it possible to use the garland without the remote control if it is lost or defective?

Yes, most models of the "horse tail" garland allow mode switching using the button on the control unit. In the event of loss or malfunction of the remote control, modes and static illumination may be selected directly on the unit; however, timer and brightness adjustment functions available via the remote control may be unavailable.

What should be done if the garland was delivered with an incorrect glow color or without the declared remote control?

If the declared remote control is missing from the package or the actual glow color does not correspond to the description, such a situation should be regarded as non-compliance of the product with the stated characteristics. In this case, the seller recommends arranging a return through the personal account and, if necessary, placing a new order for the required modification of the "horse tail" garland.

Is an expert examination required when returning a defective garland?

The service procedure description indicates that, in order to return a garland due to defect, it is sufficient to submit a request through the personal account of the marketplace. A separate expert examination on the part of the buyer is generally not required; the decision regarding the return is made by the platform. In disputed situations, it is recommended to contact the marketplace support service.

Why is a squeaking sound sometimes heard in rhythm with the flashing of the garland during controller operation?

A slight high-frequency sound from the controller during mode switching is a feature of operation of certain electronic units. However, a pronounced constant squeaking sound accompanying flashing may indicate a malfunction or defect. In such a situation, the manufacturer recommends arranging a return of the product due to defect for diagnostics and replacement.

Is it permissible to use the garland "horse tail" on an outdoor tree and other outdoor objects?

Outdoor use is permitted only for those models in which it is explicitly stated in the description that they are intended for outdoor operation and are equipped with a moisture-protected power supply unit. Such modifications may be used for decorating outdoor trees, shrubs, and facades within the declared temperature range. Indoor versions of the "horse tail" garland designed for interior use must not be used in open air.

Is there a certificate of conformity for the garland and may it be used in children's institutions or offices?

A certificate of conformity has been issued for the "horse tail" garlands, and a copy is included in the product documentation. Upon request, the seller provides a scanned copy of the certificate by electronic mail. When used in kindergartens, schools, or offices, the instructions and recommendations for safe operation must be strictly observed.

.

How does the "horse tail" garland differ from a "dew" type garland?

The "horse tail" garland and the dew-type garland are based on the same principle of thin wired strands with miniature light-emitting diodes. The difference lies in the configuration and marketing designation: in the "horse tail" version, the strands are structurally gathered into an upper bundle and hang downward, whereas the dew type is more often supplied as long individual strands intended for free winding.

What are the main numerical parameters of the "horse tail" garlands?

LED garlands of the "horse tail" type are characterized by the following numerical parameters: strand length is typically 2 or 3 m, the number of strands in the bundle is approximately 10, 20, or 30, and the number of LEDs on each strand is approximately 30 units. As a result, the total number of diodes on the garland is approximately 200, 300, 400, 600, 800, 900, or 1200 depending on the modification. The distance between diodes on a strand is about 10 cm. For outdoor models, operating temperature ranges are specified from approximately −10 to +35 ℃ or up to −40 ℃, and in certain versions the timer operates according to schemes of 6 hours on and 18 hours off or 8 hours on and 8 hours off. The length of the power cable from the upper bundle to the plug for different articles is approximately 0,4–0,5 m or up to 3 m, which should be taken into account when selecting an extension cord.

Related articles:
Outdoor LED Icicle Garland IP44 user reviews
Outdoor LED Icicle Garland IP44 FAQ and practical recommendations

Lighting equipment manuals

MINI Laser Stage Lighting projector manual
Led Crystal Magic Ball Light disco sphere manual
Astronaut projector night light manual
DEW Garland Manual