PS2-WLC Controller Gaming Controller Manual
Playstation®, PS2, PSone, and PSX are registered trademarks of Sony Computer Entertainment, Inc. This product is not manufactured by SONY, technical support is not provided by Sony, and functions and/or specifications may change without prior notice.
We hope you enjoy using our PS2™ wireless controller operating at 2.4 GHz. Please read this manual carefully before using the device.
.Gamepad Layout and Control Buttons
1. 4-WAY directional button
2. TURBO button
3. SELECT button
4. PROGRAM button
5. START button
6. CONNECT button
7. 
button
8. 
button
9. 
button
10. 
button
11. RIGHT ANALOG JOYSTICK (press for R3)
12. RX reception LED
13. ANALOGUE button
14. Mode LED
15. LEFT ANALOG JOYSTICK (press for L3)
16. X button
17. R1 button
18. Power switch
19. Battery compartment
20. L1 button
21. L2 button
Wireless Receiver
22. Connector plug
23. RX LED
24. Connect button
25. Power indicator
Device Description
This device is a wireless controller specifically designed for use with PlayStation 2™. It can also be used with PSONE™ and PSX™. The controller operates at 2.4 GHz, features dual vibration feedback, and includes all functions of original SONY devices. The controller also supports Turbo and programmable functions.
Package Contents
- Controller
- Receiver
- User manual
Technical Specifications
Power supply: 3 x AAA 1.5 V batteries
Operating time: over 6 hours
Transmission: multi-channel 2.4 GHz
Operating range: 10 m
Special functions: Turbo function, programmable buttons with memory, forced connection
Connecting the Receiver
Insert the receiver plug (22) into the corresponding PlayStation™ console port and then switch on the PlayStation™. The receivers power indicator (25) will light up. The RX LED (23) will illuminate once the receiver connects to the controller.
.Installing / Replacing Batteries
Before using the controller, insert batteries into the battery compartment (19) on the back of the device. Open the compartment, insert new batteries according to polarity, and close the cover. Ensure the controller is switched off before use. Please also follow safe battery disposal guidelines.
Note:
Use only batteries or rechargeable batteries with a nominal voltage of 1.5 V. Always insert batteries according to correct polarity. Replace batteries with the same brand or equivalent type.
Incorrect replacement may cause explosion.
Do not attempt to recharge non-rechargeable batteries. Explosion hazard.
Batteries/rechargeables can be fatal if swallowed. Keep out of reach of children. In case of ingestion, seek medical help immediately.
Do not expose batteries to heat or fire. Never short-circuit batteries; never force them open; never attempt to recharge non-rechargeables. Otherwise, they may explode and cause serious injury.
Never replace batteries in explosive environments.
During battery installation or replacement, sparks may form, which could cause an explosion. Potentially explosive zones are often marked but not always. They include fueling stations, ship holds, fuel storage areas, tanks, and locations with chemical vapors, grain dust, or metallic powder, as well as any area where you are normally asked to turn off your car engine.
Power On/Off
The power switch (18) is located on the back of the device. To switch off the device, move the switch from OFF to ON.
Connecting the Controller
Pairing mode will activate once the power switch (18) on the bottom of the device is set to ON. The RX LED (12) and MODE LED (14) will briefly light up simultaneously.
When the RX LED (12) lights up, the device is attempting to connect to the receiver. The RX LED (12) turns off once the connection is established.
.Forced Connection
If several wireless controllers are connected simultaneously, you can use the forced connection method to select one controller.
Press the CONNECT button (6) on the controller, then press the CONNECT button (24) on the receiver within 15 seconds to establish a connection. Next, press the L3 button (15) and the SELECT button (3) on the controller, as well as the CONNECT button (24) on the receiver simultaneously for 15 seconds.
Mode Selection
Many games support analog controllers, which provide more precise input than digital controllers.
To switch between digital and analog modes, ensure that the connection to the receiver has been established. Then press the ANALOGUE button (13).
(!) The MODE LED (14) lights up in analog mode. The MODE LED (14) is off in digital mode.
Note:
Default mode is digital.
Not all games support digital mode.
You may need to quit the game before switching between modes.
Power-Saving Mode
The device includes a power-saving mode to conserve energy and extend battery life.
This mode activates in the following cases:
if no connection is established between the controller and receiver within 3 seconds
when the device and receiver are connected but the controller is idle for 3 minutes
when the connection between the controller and receiver is interrupted and not reestablished within 6 seconds
when you press the CONNECT button (6) on the controller without pressing the CONNECT button (24) on the receiver within 15 seconds.
If your device enters power-saving mode, press the START (5), L3 (15), or R3 (11) buttons to reactivate the controller.
.TURBO Function
With the TURBO function, you can switch the , , , , R1, R2, L1, and L2 buttons to TURBO/rapid fire mode. The controller must be connected to the receiver to activate or deactivate the TURBO function.
To Activate:
Press and hold the TURBO button (2) until the RX LED (12) lights up.
Then press the button you want to assign the rapid fire function to.
To Deactivate:
First press the button you want to reset. Then press and hold the TURBO button (2) until the RX LED (12) turns off.
(!) The RX LED (12) lights up when you assign the TURBO function; the RX LED blinks when the TURBO function is in use.
Button Programming Function
You can program and save a sequence of button presses using the PROGRAM function.
Setting the PROGRAM Function:
Press the PROGRAM button (4). The RX LED (12) will light up. Now press the button you want to program with a combined function. Then press the desired sequence of buttons (up to 15), and finish by pressing the PROGRAM button again. The RX LED will turn off.
Clearing the PROGRAM Function:
Press the PROGRAM button (4) once. The RX LED will light up. Press the button you previously programmed and want to reset. Press the PROGRAM button again. The RX LED will turn off, meaning the programming function is disabled.
The following buttons can be programmed with combined functions: L2, L3, R2, R3.
The following buttons can be used for programming:
, , , , all 4 directional buttons, L1,
L2, L3, R1, R2, and R3. When the device is powered off, the controller retains the last PROGRAM function setting.
(!) The RX LED (12) remains lit when the PROGRAM function is set; the RX LED (12) blinks when the PROGRAM function is in use.
Note:
Not every game supports programming button sequences.
Vibration Mode
The device will vibrate briefly once to confirm when pressing the R3 and SELECT buttons. This means all vibration (strong and weak) has been disabled. Press the same buttons again to re-enable vibration mode. This is confirmed by two short vibrations.
.Safety Instructions
Do not attempt to disassemble, modify, or repair the device yourself.
Do not use this device with other electronic equipment operating on the same frequency to avoid damage to both devices.
Ensure that liquids or small metal objects cannot enter the device. Avoid impacts and do not place heavy objects on it. Do not place containers with liquids such as vases or drinking glasses on or near the device, and never immerse it in liquid.
Do not use or store the device in areas with high temperatures, or in steamy, smoky, or dusty environments.
Never mix battery types and never mix old and new batteries. Replace batteries once they become too weak or if the device has not been used for some time.
Explosion hazard if batteries are replaced improperly. Always insert batteries according to correct polarity. Replace batteries with the same brand or equivalent type. Risk of explosion if not replaced correctly.
Do not attempt to recharge non-rechargeable batteries. Explosion hazard.
Batteries/rechargeables can be fatal if swallowed. Keep batteries out of reach of children. If swallowed, seek immediate medical assistance.
Do not expose batteries to heat or fire. Never short-circuit batteries; never force them open; never attempt to recharge non-rechargeable batteries. Otherwise, batteries may explode and cause serious injury.
Battery Disposal
Please note that as an end user, you are obliged to return used batteries to public or private battery collection facilities.
Device Disposal
Please note that this device falls under European Directive 2002/96/EC on electronic waste reduction:
You are not allowed to dispose of this device with household waste. Information on safe disposal is available from your local council, waste management authority, and the retailer where you purchased the product.
You can return this product free of charge to your local collection center. Proper disposal of used products protects the environment and your health.
Warranty
This product comes with a three-year warranty starting from the date of purchase. If this product is defective, send it along with the receipt and a stamped self-addressed envelope to:
JNC Datum Tech GmbH, Support Center,
Maltschachstrasse 32, D - 72144 Dusslingen, Germany.
Manufacturer:
JNC Datum Tech GmbH, Benzstrasse 33, D - 71083 Herrenberg
Germany
Instructions operating manual for remote controls, keyboards |