User guide for the Xiaomi Dreame F9 Robot Vacuum (RVS5-WH0) robot vacuum cleaner

Operating Instructions for the Xiaomi Dreame F9 Robot Vacuum (RVS5-WH0) robot vacuum cleaner

Thank you for choosing the Dreame F9 Robot Vacuum! Before first use, please read this manual carefully.

Product Overview

1. Power/Clean button

Power on or off: press and hold for 3 seconds

Status indicator

White indicator: cleaning in progress or cleaning completed
Flashing white indicator: cleaning paused
Flashing blue indicator: network connection in progress
Flashing orange indicator: error

2. Local cleaning/Dock button

Press to send the robot vacuum with mopping function back to the dock for charging. Press and hold for 3 seconds to enter the designated area cleaning mode.

3. Visual navigation sensor

4. Lid latch

(!) Note: Specifications and appearance may vary; the actual product takes precedence.

1. Reset button

Press and hold this button to restore factory settings

2. Wi-Fi indicator

Flashing signal: connected to Wi-Fi
Slow flashing: waiting for connection
Fast flashing: connecting

3. Brush cleaning tool

4. Exhaust outlet

5. Infrared braking sensor

6. Cliff sensors

7. Omnidirectional wheel

8. Charging contacts

9. Optical sensor

10. Side brush

11. Main wheels

12. Main brush

13. Brush guard clips

14. Bumper

Accessories

1. Container latch

2. Container lid

3. Filter

4. Signal area

5. Charging contacts

6. Power port

7. Water tank

8. Water tank plug

9. Mopping pad

10. Attachment area

Operation

Preparation for use

1. Remove the protective film

2. Install the side brush

3. Place the charging dock on a flat surface against a wall and connect the power

(!) Notes:
1. Ensure at least 0.5 meters of space on each side of the dock and more than 1.5 meters in front;
2. Remove unsecured cables—the robot may pull them and disconnect the dock;
3. For device setup, the charging dock must be within the Wi-Fi coverage area;
4. Do not place the charging dock under direct sunlight and do not block the positioning beacon; otherwise, the robot will not be able to return to the dock automatically.

4. Place the robot on the charging dock

Battery level indicator

White: battery level above 15%
Orange: battery level below 15%

(!) Notes:
1. Fully charge the device before first use;
2. Do not install the mopping module while charging.

Connecting to the app

Use the product with the Mi Home app.

To download the app, search for "Mi Home" in Google Play or the App Store. Alternatively, you can download the app by scanning the QR code (for Android devices).

(!) Note: Due to software updates, the actual steps for connecting the device may differ; please follow the on-screen prompts.

Wi-Fi reset

If you encounter any Wi-Fi issues, reset the Wi-Fi settings to the default values.

To do this, press and hold the and buttons simultaneously until you hear the message that the device is waiting for network configuration. As soon as the indicator begins to flash slowly, the Wi-Fi will be reset.

Open the top cover. Press the system reset button using a paper clip or toothpick. Hold it until you hear the voice message "Restore factory settings" in English or Chinese. Release the Dreame F9 Robot Vacuum reset button. Allow Dreame time to restore default settings.

Powering on and off

Press and hold the button to turn on the robot vacuum with mopping function. If the power indicator is steadily white, the robot vacuum is in standby mode.

To turn off the robot vacuum, press and hold the button when it is stopped. Turning off the robot vacuum will end the current cleaning task.

Starting cleaning

After activation, the robot vacuum will clean each room using an S-shaped pattern and then move along walls and corners to finish. When cleaning is complete, it will automatically return to the dock to charge.

Cleaning modes

Four modes are available in the app: Quiet, Standard, Strong, and Turbo. Standard mode is set by default.

Pause/Sleep mode

Press any button to pause the robot vacuum during cleaning.

If no action is taken within 10 minutes, the robot vacuum will automatically enter sleep mode, and the power and charging indicators will turn off. Press any button to wake the robot vacuum.

(!) Note: The robot vacuum will not enter sleep mode until it is fully charged.

Local cleaning mode

If the robot vacuum is in standby or paused, press and hold the button for 3 seconds to enter spot cleaning mode. In this mode, it will clean an area of 1.5 x 1.5 meters around itself.

After spot cleaning is completed, the robot vacuum will automatically return to its initial position and power off.

Do Not Disturb mode

Do Not Disturb mode prevents the robot vacuum from automatically performing cleaning tasks. The power indicator remains off. You can disable Do Not Disturb mode or adjust its hours in the app.

(!) Notes:
1. Scheduled cleaning will still be performed during the Do Not Disturb period;
2. The robot vacuum will resume cleaning after this period ends.

Scheduled cleaning

You can set a cleaning schedule in the Mi Home app. The robot vacuum with mopping function will automatically start cleaning at the set time and return to the dock for charging after completion.

Advanced features

The app can be used to configure advanced features such as selected room cleaning, zoned cleaning, and no-go zones (available when map saving is enabled).

Mopping function

It is recommended to vacuum all floors at least three times before the first mopping session to achieve better cleaning performance.

1. Install the mopping pad

Moisten the pad and wring out excess water. Insert the pad fully into the slot of the water tank until it is securely fixed.

2. Fill the water tank

Open the water tank lid, fill it with water, and close the lid securely.

(!) Note: Do not use detergents or disinfectants!

3. Install the mopping module

Align it as shown in the illustration, then slide it into the rear of the robot vacuum until you hear a click.

(!) Notes:
1. Use the mopping mode only when someone is at home. To prevent the robot vacuum from climbing onto carpets, you can use various objects as barriers;
2. Use the app to adjust the water flow.

4. Removing the water tank

Press the two side latches inward and slide the water tank backward to detach it from the robot.

(!) Notes: When the robot vacuum is charging or not in use, remove the mopping module, empty the remaining water from the tank, and clean the mopping pad to prevent mold and unpleasant odors.

Troubleshooting

The robot vacuum does not power on

1. Low battery level. Charge the robot vacuum and try again;
2. Check the ambient temperature. The operating temperature range is 0 to 40 degrees.

The robot vacuum does not charge

1. The dock is not connected to power. Ensure both ends of the power cord are properly connected;
2. Poor contact. Clean the charging contacts on the dock and the robot vacuum.

The robot vacuum does not return to the dock for charging

1. Obstacles detected around the charger. Place the charging dock in a more open area;
2. Clean the dock’s signal area.

The robot vacuum makes unusual noise

1. A foreign object may be stuck in the main brush, side brush, or one of the wheels. Stop the robot and remove any debris.

The robot vacuum has stopped

Turn the robot vacuum off and restart it.

The robot vacuum cleans inefficiently or leaves debris

1. The dustbin is full; empty it;
2. The filter is clogged; clean it;
3. A foreign object is caught in the main brush; remove it.

The robot vacuum cannot connect to Wi-Fi

1. Weak Wi-Fi signal. Move the robot vacuum within the Wi-Fi coverage area;
2. A problem occurred when connecting to the Wi-Fi network. Reset the Wi-Fi settings and install the latest version of the app, then try to connect again.

The robot vacuum does not perform scheduled cleaning

1. Low battery level. Scheduled cleaning will not start until the battery level is at least 15%.

Questions and Answers

Does the robot vacuum consume power if it remains on the charging dock after being fully charged?

When left on the dock after a full charge, the robot vacuum consumes very little energy, which helps maintain optimal battery performance.

Is it necessary to charge the robot vacuum for 16 hours during the first three uses?

Lithium batteries do not have a memory effect; therefore, there is no need to wait 16 hours for a full charge.

What should I do if the mopping module does not dispense water or dispenses very little?

Make sure the water tank is filled, clean the mopping pad if necessary, and ensure it is installed correctly.

What should I do if the mopping module dispenses too much water?

Make sure the water tank lid is closed.

Specifications

Robot vacuum

Model: RVS5-WH0
Battery: 14.4V / 5200 mAh
Connectivity: Wi-Fi IEEE 802.11 b/g/n, 2.4 GHz
Mobile app: Mi Home
Rated power: 40W
Operating temperature: From 0° to +40°C

Docking station

Model: RCS0
Input parameters: 100 – 240V ~50/60 Hz, 0.5A
Rated output: 19.8V/1A

Disclaimer

Changes or corrections may be made to this user manual at any time without notice due to typographical errors, inaccuracies in current information, or improvements to software and hardware.

All illustrations are for demonstration purposes only and may not exactly represent the actual device.