Operating manual for the Underwater Fishing Camera Fisher CR110-7L

Underwater Fishing Camera Fisher CR110-7L User Manual

Application

This measuring instrument is intended for detecting metals (ferrous and non-ferrous, e.g., reinforcing steel) in walls, ceilings, and floors; for locating wooden beams; as well as for finding live electrical cables under voltage.

Technical Specifications

Power supply: 12.6 V battery (4500 mAh)
Input voltage: 110 V ~ 220 V
Operating time with a fully charged battery: up to 12 hours
Package size: 220x190x115 mm
Gross weight: 2 kg
Storage temperature: -30 °C...+70 °C
Operating temperature: -20 °C...+60 °C

Camera

Resolution: 800 TVL
Viewing angle: 140°
Illumination: 12 LEDs
Cable length: 15 meters

Monitor

Screen resolution: 800x480 pixels
Diagonal size: 7" (approximately 18 cm)
Power: 12 V
Image adjustments: brightness, contrast, color saturation

(!) ATTENTION! For brand development and improved consumer properties, the manufacturer reserves the right to modify, update, and enhance the device at its own discretion.

(!) ATTENTION! The device appearance, scope of delivery, and specifications may be changed by the manufacturer without prior notice. All illustrations in this manual are schematic representations and may differ from the actual appearance. The description is for reference only and cannot serve as a basis for claims or complaints.

Appearance

1. REC / "-" (record / decrease) — enable/disable recording mode; decrease the numeric value of a parameter.
2. PLAY / "+" (playback / increase) — select/playback; increase the numeric value of a parameter.
3. MENU/EXIT (menu / exit) — button for entering/exiting and navigating the settings menu.
4. ▶ (right) — used for navigating the settings menu and for quick photo capture.
5. ◀ (left) — used for navigating the settings menu and for entering the gallery.
6. — ON/OFF: power button for the monitor screen

Connection

First connect the battery to the monitor power cable, then connect the power output cable and the input AV connectors.

NOTES:

After installing a new SD card or if the SD card is damaged, press the REC button to check it. The device will prompt you to format the memory card. Press the "" button to select [Yes] or [No], and then press the MENU button to confirm your selection.

The current time and date are always displayed in the lower right corner of the screen. The MENU/EXIT button is also used to exit any operating mode.

Installing the Float and Hook

Thread the fishing line through the hole at the top of the float; adjust the line length as required. Then select an appropriate position on the camera cable and secure the float (see the illustration below).

Installing the Fishing Hook

Mounting multiple hooks: typically 2 to 3 hooks are attached in series on the line. Each hook should be positioned 5 cm from the next (for verification, monitor the image on the screen). Leave extra line to attach a sinker after connecting the final hook. Parallel mounting of hooks: as a rule, 2 hooks are attached to the line; the line length is adjusted according to water transparency. Avoid twisting the hooks during installation.

NOTE:

Do not attach the fishing line with a hook directly to the camera cable. This may damage the cable. Attach the line to the dedicated groove on the camera housing.

Charge the device regularly as the battery level decreases.

To do this:
1. Remove the battery and the charger from the box.
2. Connect the charger to the battery.
3. Plug the charger into a 220 V AC outlet.
Charging will begin.

Operating in Digital Video Recorder (DVR) Mode

Before enabling the video recording (DVR) function, make sure that a memory card is installed in the device. To do this, check the memory card slot located on the left side panel of the monitor (see the image below).

Observation in DVR Mode

Press the MENU button to access the settings and press it again to select/change parameters. Navigate between menu items using the ◀ ▶ buttons, and use the PLAY button to select a menu item.

Use the REC/? and PLAY/+ buttons to decrease or increase the numeric value of the current parameter. In the date and time settings, press PLAY to enter the setting mode, and then press ◀ ▶ to change the time and date values.

Video Recording

Press the REC button to start video recording. To stop recording, press this button again.

Video playback: press the PLAY button to play the recorded video file; press the button again to stop playback. Press ◀ ▶ to display the next and previous video recordings.

Creating and Viewing Photographs

Press ◀ ▶ to display snapshots taken by the camera, and press ◀ ▶ sequentially to navigate between photos.