TORRES SW-1 / SW-2 Stopwatch Operating Manual

TORRES SW-1 / SW-2 Stopwatch Instruction Manual

Package contents:

- Stopwatch – 1 pc.
- Battery – 1 pc.
- Cord with plastic clip – 1 pc.

Technical specifications:

1. Time (hours, minutes, seconds) displayed in 12/24 format;
2. Calendar (month, date, day of the week);
3. Alarm with snooze and hourly chime functions;
4. Stopwatch with an accuracy of 0.01 sec and split time function;
5. Maximum stopwatch time display: 23:59:59.

Mode switching:

In normal mode, the display shows hours, minutes, seconds, and the day of the week.

1. Press and hold #1
Month and date

2. Press and hold #2
Set alarm time, alarm on/off symbol, hourly chime indicator

3. Press #3
Stopwatch mode

4. Press #3 again
Alarm time setting

5. Press #3 again
Time setting mode

6. Press #3 again
Return to normal mode

(!) Note: The stopwatch has two #3 buttons which differ only in their position.

Setting time and date:

1. Press #3 three times; “seconds” will flash. Press #1 to reset seconds. To ensure accuracy, it is recommended to reset seconds at the end of the setting procedure.

2. Press #2 to set minutes. Adjust minutes by pressing #1. Holding #1 accelerates the adjustment.

3. Press #2 to set hours. Adjust hours by pressing #1. To select 24-hour format, increase the value until the letter H appears to the right of the hour. To select 12-hour format (AM/PM), continue increasing the value until the letter A (00:00 to 12:00) or P (12:00 to 00:00) appears. Holding #1 accelerates the adjustment.

4. Press #2 to set the date. Adjust the date with #1.

5. Press #2 to set the month. Adjust the month with #1.

6. Press #2 to set the day of the week. Adjust the day with #1 (S - Sun, M - Mon, T - Tue, W - Wed, T - Thu, F - Fri, S - Sat).

7. Press #3 to return to normal mode.

Stopwatch:

1. Press #3 to select stopwatch mode. Press #1 to start/stop the stopwatch. To reset, stop the stopwatch with #1 and then press #2 to clear the time.

2. To record split time while the stopwatch is running, press #2. The split time will be displayed while the stopwatch continues counting in the background. To view the current running time, press #2 again.

3. Press #3 to exit stopwatch mode. Timing will continue unless the stopwatch has been stopped.

Alarm setting:

1. Press #3 twice, the “alarm hours” will flash on the screen. Set the hours by pressing button #1.

2. Press #2 to set the “alarm minutes.” Adjust the minutes using button #1.

3. Press #3 to return to normal mode.

Holding button #1 allows accelerated value adjustment.

Alarm operation:

1. To enable/disable the alarm, press and hold button #2, then press button #1. When the alarm is enabled, the corresponding icon is displayed in the upper right corner of the screen.

2. At the set time, the alarm will sound. Pressing button #1 will silence the alarm, but it will repeat after 5 minutes. To completely turn off the signal, press button #2. If neither button #1 nor button #2 is pressed, the alarm will automatically stop after 60 seconds of sounding.

3. When enabled, the alarm will sound daily at the set time.

Hourly chime

1. While holding button #2, press button #3 to enable/disable the hourly chime.

2. When this mode is active, the day-of-the-week symbols are underlined on the display.

Battery:

If necessary, for example, when the display brightness decreases, replace the battery located under the cover on the rear panel of the stopwatch. Use LR44 battery or an equivalent.

Warranty period of operation:

The manufacturer’s warranty for the stopwatch is 6 months from the date of purchase.